Fix Error code E061-0000 Canon IR 5000/6000/6570

Fix Error code E061-0000.Error e061 for according to glasses technician is error code often once seem , especially for type machine canon ir 5000 or ir 6000,The cause of error e061 are not always the same, not all machine that experienced e061 be the same way resolution.

Several components this need you check if machine issued error code e061 , the components was;

1.Primary Charger

2. HVT

Of both the components , usually into the cause of the emerge of error code e061 , and how a way to deal with the e061 error code , the following is my experience he when overcome machine photocopy appear error e061

How to Fix Error code E061-0001

This is experience in the field when overcome error e061

1. Setting Primary charge Wire
The first step to overcome error code e061 is by seeing wire charge conditioned  yet because more than one primary , clean up beforehand wire - wire him to righteous anger with alcohol or other cleaning , after it is clean doing a suit on wire him , authentication is required to set wire up a sense of anticipation in the middle or a bit of closely resembled those of the of a drum , switch off and machine back to life , if still to appear code e061 , trying to do fit with the clear error and let have a back causes death and cranked away at all the . Usually this way struggled to come to terms.

2. Setting Po Cont
The second way in which when in urgent situations is a look at an as many points right away po cont , although this is not a long-term solution but with change these numbers po cont from 1 to 0 , could make a severe inroad and he will remove the code error e061 , for a machine that it is still good , by replacing po cont desired investment growth figure could not think that this will influence the outcome of copier supplies , but for a machine that are old damn it , so the results of usually copier supplies cannot be ideal .

3.Replace HVT
When second solution above; t get over error code e061 , so the last step is by replacing hvt , replacement hvt usually marked when replace po cont into figures 0 still catching up error e061 . If it happens that it when his you try to replace hvt.

It still needed to gather based on our experience to overcome code error e061 , hopefully i can help

Canon IR 4570 E110-000

Canon IR 4570 E110-000.A laser unit is a component was vital to the establishment of a copy of document . Of the functions laser work this is documents can be in copy for many fold . If damage occurs on a laser , fotocopy machine will issue such a code error e100 or e110 .

now we will discuss the cause of e110.

e110 is caused by malfunction of polygon laser motor, this laser is inside laser unit.polygon motor damage is usually caused by:

wire laser unit
1.Broken / broken / conslet cable

2.The polygon motor is broken.
motor polygon one of coused e110 canon

how to solve e100

1.Replace the laser unit with a good laser
if by replacing the laser unit the problem is solved means it is a broken polygon motor.

2.Check wire
if replacing the laser does not disappear e110, then check wire, do break, konslet etc,

3.Replace dc
replace the DC if the above two options do not also overcome e110.

Fix Error E001-0003 Canon IR 5000

Fix Error E001-0003 Canon IR 5000.the fixing unit is a very vital component of the photocopy machine, this is where the paper will be heated, so that the trainer can be firmly attached to the paper.components in a fixing unit such as a heater, the thermostat must be in good condition. if one of the components is damaged, then E001 error will appear, as in this case E001-0003.

E001-0003 on the field is often caused by the Main thermistor or Sub thermistor is damaged, the damage is due to charred or broken.

How to Resolve e001-0003.

1.Replace Main Thermistor and sub thermistor.
case field just enough replaces both these components, then e001-0003 immediately lost, if not lost go to the second option.

main and sub thermistor ir 5000


2. Replace AC Driver
AC drivers need to check if replacing the main thermistor and sub thermistor can not solve the problem e001-0003, because the electric current leading to the heater comes from AC driver. so AC driver is also needed to test.

AC driver ir 5000


How to check main thermistor and sub thermistor.
this is how I think to check whether the main thermistor and sub thermistor is still good or damaged.

Check main thermistor and sub thermistor good or damaged

1.Prepare Multytester

2. Prepare Fire, from solder or etc.

3.Insert the multytester cable into each main cable socket or sub thermistor.

4.Bring the soldering heat to the main or sub thermistor.

5.If the main thermostat is good, then the multytester needle will move up, if it is broken then the needle will be silent.

so how to resolve E001-0003 error, hope it helps

Fix error code e004-001 canon ir 5050,5075,5070,6570

Fix error code e004-001 canon ir 5050,5075,5070.Strongly influenced the durability of voltage copier supplies that you use ,Machine that are voltage in areas with a stable tending to more durable Compared to a photocopy in areas with voltage unstable.For fear of a massive voltage photocopy machine components,Some error will arise when electricity was no steady as e004-001,What caused the and how to handle it.
IH Control IR 6570

Fix error code e004-001.Code error e004-001 voltage appear as the effect unstable,A faulty component focuses on the part that directly touch with electricity,Call  its own power supply , IH power and dc . Of several been the case field,E004-001 more often because the mal-function of power IH,Because IH power is working to stabilize the current in units 1,So where is the current positions of the power IH?.

Once you have in the dark on part that is probably as the cause of that is IH power , then afterward will you unload IH power who are on the left machine.

Location of IH Control in ir 6570


As i said , if IH power is not replace that could resolve problems ,so please go to DC control .

So an overview of overcome e004-001 a canon ir 5050,5070,5075 hopefully useful.




Resolve error code e100-0001

Resolve Error Code E100-0001.the e001-0001 code error that appears on the copy machine is generally the same for all types of canon engines. as happened to my machine canon IR 2200,as happened to my machine canon IR 2200, when yesterday the machine is still good,

error code e100-0001

the cause of the emergence of the code e100-0001, according to the manual service manual is associated with the Lase Unit, the laser unit is under the finisher. from the confused is what makes my machine appeared error E100-0001.

disconnected cable laser,couse e100-0001


Overcoming errors e100-0001. I just disassemble the laser unit, it turns out the laser cable bitten by a rat. because I do not have laser spare parts, then the disconnected cable I connect and in solder.

so how do i resolve the error e100-0001 so it can get back to normal.